Avocent Network Adapter EMS1000P Guía de usuario Pagina 74
- Pagina / 80
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Command Description
AT&D3
ON-to-OFF transition causes the modem to perform a soft reset. It is the same as if an ATZ command is
issued.
AT&F Restores factory configuration.
AT&G0 Disables guard tone (default).
AT&G1 Enables 550-Hz guard tone.
AT&G2 Enables 1800-Hz guard tone.
AT&K0 Disables flow control.
AT&K3 Enables RTS/CTS flow control (default for data modes).
AT&K4 Enables XON/XOFF flow control.
AT&K5 Supports transparent XON/XOFF flow control.
AT&P0 39/61 make/break ratio at 10 pulses per second (default).
AT&P1 33/67 make/break ratio at 10 pulses per second.
AT&P2 39/61 make/break ratio at 20 pulses per second.
AT&P3 33/67 make/break ratio at 20 pulses per second.
AT&Q0 Selects direct asynchronous operation.
AT&Q5 Modem will try an error-corrected link.
AT&Q6
Selects asynchronous operation in normal mode (allows speed buffering and flow control but no error
correction).
AT&V
Displays modem’s current configuration. When this command is entered, the modem will display its current
command and register settings.
AT%C0 Disables data compression.
AT%C1 Enables MNP 5 data compression.
AT%C2 Enables V.42 bis data compression (sets S46 bit 1).
AT%C3 Enables V.42 bis and MNP 5 data compression (default).
AT%E0 Disables line quality monitor and auto-retrain.
AT%E1 Enables line quality monitor and auto-retrain.
AT%E2 Enables line quality monitor and fallback/fall-forward (default).
AT%L Line signal level. Returns a value that indicates the received signal level. Example, 009 = -9dBM.
AT%Q
Line signal quality. Reports line signal quality (DAA-dependent). Returns higher order byte of the EQM value.
Based on EQM value, retrain or fallback/fall-forward may be iniated if enabled with AT%E1 or AT%E2
commands.
AT+MS Select/force modulation.
AT+MS modulation selection
This extended-format compound parameter controls the manner of operation of the modulation capabilities in the
modem. It accepts six sub-parameters:
+MS=<carrier>, <automode>, <min_tx_rate>, <max_tx_rate>, <min_rx_rate), <max_rx_rate><CR>.
To read the current settings, enter AT+MS?<CR>
Modulation Carrier Description
Bell 103 B103 300
Bell 212 B212 1200
V.21 V21 300
V.22 V22 1200
Table E.3: +MS Command Supported Rates
66 Cyclades™ ACS 6000 Advanced Console Server
- INSTALLER/USER GUIDE 1
- European Union Notification 2
- USA Notification 2
- Canadian Notification 2
- Japanese Notification 2
- Korean Notification 2
- Installer/User Guide 3
- Symbols Used 4
- Introduction 1 5
- Installation 7 5
- Appendices 59 7
- Introduction 9
- Web manager 10
- IPv4 and IPv6 support 10
- Flexible users and groups 10
- Security 10
- Authentication 11
- Packet filtering 11
- Configuration Example 12
- Chapter 1: Introduction 5 13
- Installation 15
- Connecting the Hardware 16
- Turning On the Console Server 19
- Configuring a Console Server 20
- Wizard Mode 24
- Expert Mode 26
- System Tools 26
- DSView 3 software security 27
- FIPS module 27
- HTTPS Certificate 28
- Bootp Configuration Retrieval 29
- Date and Time 30
- Help and Language 30
- Boot Configuration 31
- Information 32
- Settings 32
- IPv4 and IPv6 static routes 33
- Firewall 34
- IPSec(VPN) 36
- SNMP Configuration 37
- Serial ports 38
- Table 3.6: Dial-in Parameters 41
- Table 3.7: Power Parameters 42
- Auxiliary ports 43
- CAS Profile 43
- Auto discovery 44
- Pool of CAS ports 45
- Dial-in Profile 46
- Dial-out Profile 47
- Pluggable Devices 49
- Appliance authentication 50
- Authentication servers 50
- Local accounts 52
- User groups 53
- Managing user groups 55
- Table 3.11: ts_menu Options 56
- DSView software access rights 58
- Event Notifications 59
- Trap Forward 60
- Data Buffering 60
- Appliance logging 60
- Power Management 61
- Outlet Groups 63
- Active Sessions 64
- Monitoring 65
- Change Password 65
- Serial Viewer 66
- App e nd ic e s 67
- DSView 3 Software 69
- Appendix E: Internal Modem 72
- Appendices 65 73
- AT+MS modulation selection 74
- AT S registers 75
- Basic modem result codes 76
- Digital line guard 76
- Sleep mode operation 76
- Disconnecting a call 77
- Selecting country codes 77
- Using caller ID 78
- Appendix F: Technical Support 79
- For Technical Support: 80
Relacionado con productos y manuales para Servidores De Consola Avocent Network Adapter EMS1000P
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.092 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales