Avocent Network Adapter EMS1000P Guía de usuario Pagina 40
- Pagina / 80
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Parameter Description
Enable Speed
Auto
Detection
Tries to discover the speed of the serial port. This feature requires additional configuration under the CAS
Profile / Auto Discovery / Settings page. Default: Disabled.
Protocol
The protocol that will be used by authorized users to access the serial port/target. The console server
accepts three protocols for connection to the target: Telnet for telnet connection, SSH for secure
connection and Raw Mode for raw socket connection. An administrator can configure the port to accept
one, two or all three types. NOTE: Raw protocol requires the configuration of the Raw Mode Port Alias.
Default value: Telnet/SSH.
Authentication
Type
Authentication type that will be used to authenticate the user during target session. Default: Local.
Text Session
Hot Key
Hotkey to suspend the target session and go to the CLI prompt. Not available for Raw. Default: Ctrl-Z.
Note:The default escape character for ts_menu is Ctrl-X.
Power
Session Hot
Key
Hotkey to suspend the target session and display Power Management Menu to control the outlets merged
to the target. Not available for Raw. Default: Ctrl-P.
NOTE:The default escape character for ts_menu is Ctrl-X.
TCP Port
Alias
Telnet Port Alias: TCP port to connect directly to a serial port using Telnet protocol for the connection. SSH
Port Alias: TCP port to connect directly to a serial port using SSH protocol for the connection/ Raw Mode
Port Alias: TCP port to connect directly to a serial port using raw socket for the connection.
Port IPv4/IPv6
Alias
IPv4/IPv6 address used to connect directly to a serial port. Default: not configured (empty).
Port IPv4/IPv6
Alias Interface Interface (ETH0/ETH1) associated with the IPv4/IPv6 alias. Default: ETH0.
Allow Session
Only if DCD is
On
When the DCD is OFF, the appliance will deny access for this serial port. Default: Disabled (allow access if
DCD is OFF).
Enable Auto
Answer
When the input data matches one input string configured in Auto Answer, the output string will be
transmitted to the serial port. Default: Disabled.
DTR Mode
DTR Mode can be set to the following: Always On. Normal - the DTR status willdepend on the existence of
a CAS session. Off Interval - when the a CAS session is closed, the DTR will stay down during this interval.
Default: Normal.
DTR Off
Interval
Interval in seconds used by DTR Mode Off Interval in milliseconds. Default: 100.
Line Feed
Suppression
Enables the suppression of the LF character after the CR character. Default: Disabled.
Null After CR
Suppression
Enables the suppression of the NULL character after the CR character. Default: Disabled.
Transmission
Interval
The interval the port waits to send data to a remote client in milliseconds. Default: 20.
Break
Sequence
An administrator can configure the control key as the break sequence, entering ^ before the letter. Not
available for Raw. Default: ~break.
Break Interval Interval for the break signal in milliseconds. Not available for Raw. Default: 500.
Log In/Out
Multi Session
Notification
Enables the notification to multi-session users when a new user logs in or a user logs out. Not available for
Raw. Default: Disabled.
Informational
Message
Notification
Displays an information message when a target session is opened. Not available for Raw. Default:
Enabled.
Data
Buffering
Status Enables or disables data buffering. Default: Disabled.
32 Cyclades™ ACS 6000 Advanced Console Server
- INSTALLER/USER GUIDE 1
- European Union Notification 2
- USA Notification 2
- Canadian Notification 2
- Japanese Notification 2
- Korean Notification 2
- Installer/User Guide 3
- Symbols Used 4
- Introduction 1 5
- Installation 7 5
- Appendices 59 7
- Introduction 9
- Web manager 10
- IPv4 and IPv6 support 10
- Flexible users and groups 10
- Security 10
- Authentication 11
- Packet filtering 11
- Configuration Example 12
- Chapter 1: Introduction 5 13
- Installation 15
- Connecting the Hardware 16
- Turning On the Console Server 19
- Configuring a Console Server 20
- Wizard Mode 24
- Expert Mode 26
- System Tools 26
- DSView 3 software security 27
- FIPS module 27
- HTTPS Certificate 28
- Bootp Configuration Retrieval 29
- Date and Time 30
- Help and Language 30
- Boot Configuration 31
- Information 32
- Settings 32
- IPv4 and IPv6 static routes 33
- Firewall 34
- IPSec(VPN) 36
- SNMP Configuration 37
- Serial ports 38
- Table 3.6: Dial-in Parameters 41
- Table 3.7: Power Parameters 42
- Auxiliary ports 43
- CAS Profile 43
- Auto discovery 44
- Pool of CAS ports 45
- Dial-in Profile 46
- Dial-out Profile 47
- Pluggable Devices 49
- Appliance authentication 50
- Authentication servers 50
- Local accounts 52
- User groups 53
- Managing user groups 55
- Table 3.11: ts_menu Options 56
- DSView software access rights 58
- Event Notifications 59
- Trap Forward 60
- Data Buffering 60
- Appliance logging 60
- Power Management 61
- Outlet Groups 63
- Active Sessions 64
- Monitoring 65
- Change Password 65
- Serial Viewer 66
- App e nd ic e s 67
- DSView 3 Software 69
- Appendix E: Internal Modem 72
- Appendices 65 73
- AT+MS modulation selection 74
- AT S registers 75
- Basic modem result codes 76
- Digital line guard 76
- Sleep mode operation 76
- Disconnecting a call 77
- Selecting country codes 77
- Using caller ID 78
- Appendix F: Technical Support 79
- For Technical Support: 80
Relacionado con productos y manuales para Servidores De Consola Avocent Network Adapter EMS1000P
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales