Avocent Network Adapter EMS1000P Guía de usuario Pagina 42
- Pagina / 80
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Parameter Description
PPP Idle
Timeout
Number of seconds being idle before PPP times out. Default: 0 (no time-out).
To configure or to edit one or more serial ports with a connected PDU:
1. Select Ports - Serial Ports.
2. Click the checkbox for one or more serial ports with a connected PDU.
3. Click the Set Power button and use the drop-down menus to configure the physical settings.
4. Click Next or click the Power link.
a. Use the drop-down menu to select the PDU type.
b. Check the box to enable speed auto detection.
c. Configure the polling rate.
d. For Avocent/Cyclades PDUs, enter the power cycle interval and then use the drop-down menus to
enable or disable Syslog, Buzzer and SW Overcurrent Protection.
5. Click Save.
Parameter Description
Physical
Enable Cisco RJ-45 Pin-
Out
Defines the serial port pinout. Default: Disabled.
Status Defines the status of the serial port as either enabled or disabled. Default: Disabled.
Speed
Defines the speed as 300, 1200, 2400, 4800, 9600, 19200, 38400, 57600 or 115200.
Default: 9600.
Parity Defines the parity as either Even, Odd or None. Default: None.
Data Bits
Defines the data bits as either 5, 6, 7 or 8. Default: 8.
Stop Bits Defines the stop bits as either 1 or 2. Default: 1.
Flow Control
Defines the flow control as none, hardware, software, RxON software or TxON sofware.
Default: None.
Power
PDU Type
Defines the type or vendor of the PDU connected to the serial port.
• Auto - the vendor will be detected.
• Avocent-Cyclades - Avocent-Cyclades PM PDU family.
• SPC - SPC power control device family.
• Server Tech - Server Tech family.
Default: Auto.
Enable Speed Auto
Detection
When enabled, detects the speed of the port. Default: Disabled.
Pooling Rate The interval in seconds to update information from the PDU. Default: 20.
For Avocent/Cyclades
PDUs
Power Cycle Interval
The interval in seconds between Off and On actions for the power cycle command. Default:
15.
Syslog When enabled, the PDU will send syslog messages to the appliance. Default: Enabled.
Buzzer Enables or disables the PDU’s buzzer. Default: Enabled.
SW Overcurrent Protection
When enabled, the software’s overcurrent protection is on. Default: Disabled.
Table 3.7: Power Parameters
34 Cyclades™ ACS 6000 Advanced Console Server
- INSTALLER/USER GUIDE 1
- European Union Notification 2
- USA Notification 2
- Canadian Notification 2
- Japanese Notification 2
- Korean Notification 2
- Installer/User Guide 3
- Symbols Used 4
- Introduction 1 5
- Installation 7 5
- Appendices 59 7
- Introduction 9
- Web manager 10
- IPv4 and IPv6 support 10
- Flexible users and groups 10
- Security 10
- Authentication 11
- Packet filtering 11
- Configuration Example 12
- Chapter 1: Introduction 5 13
- Installation 15
- Connecting the Hardware 16
- Turning On the Console Server 19
- Configuring a Console Server 20
- Wizard Mode 24
- Expert Mode 26
- System Tools 26
- DSView 3 software security 27
- FIPS module 27
- HTTPS Certificate 28
- Bootp Configuration Retrieval 29
- Date and Time 30
- Help and Language 30
- Boot Configuration 31
- Information 32
- Settings 32
- IPv4 and IPv6 static routes 33
- Firewall 34
- IPSec(VPN) 36
- SNMP Configuration 37
- Serial ports 38
- Table 3.6: Dial-in Parameters 41
- Table 3.7: Power Parameters 42
- Auxiliary ports 43
- CAS Profile 43
- Auto discovery 44
- Pool of CAS ports 45
- Dial-in Profile 46
- Dial-out Profile 47
- Pluggable Devices 49
- Appliance authentication 50
- Authentication servers 50
- Local accounts 52
- User groups 53
- Managing user groups 55
- Table 3.11: ts_menu Options 56
- DSView software access rights 58
- Event Notifications 59
- Trap Forward 60
- Data Buffering 60
- Appliance logging 60
- Power Management 61
- Outlet Groups 63
- Active Sessions 64
- Monitoring 65
- Change Password 65
- Serial Viewer 66
- App e nd ic e s 67
- DSView 3 Software 69
- Appendix E: Internal Modem 72
- Appendices 65 73
- AT+MS modulation selection 74
- AT S registers 75
- Basic modem result codes 76
- Digital line guard 76
- Sleep mode operation 76
- Disconnecting a call 77
- Selecting country codes 77
- Using caller ID 78
- Appendix F: Technical Support 79
- For Technical Support: 80
Relacionado con productos y manuales para Servidores De Consola Avocent Network Adapter EMS1000P
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales