Avocent Network Adapter EMS1000P Guía de usuario Pagina 25
- Pagina / 80
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4. If you are not using DSView 3 software to manage the appliance, uncheck the Allow Appliance to be
Managed by DSView box.
5. Click Next to configure the Network or click the Network, Ports or Users link to open the appropriate
screen.
To configure network parameters:
1. Select the Network link in the content area.
2. Enter the Hostname, Primary DNS and Domain in the appropriate fields.
3. Select the IPv4 or IPv6 method for the ETH0 interface. If using Static, enter the Address, Mask and Gateway
in the appropriate fields.
4. Enable or disable IPv6 support.
5. Click Next to configure ports or click on the Security, Ports or Users link to open the appropriate screen.
To configure Ports:
1. Select the Ports link in the content area.
2. Check the box(es) to enable all ports and/or to enable Cisco RJ45 Pin-Out to change the pin-out when a
Cisco cable is connected.
3. Use the appropriate drop-down menus to select the values for Speed, Parity, Data Bits, Stop Bits, Flow
Control, Protocol, Authentication Type and Data Buffering Status.
4. Select the Data Buffering Type. If using NFS, enter the NFS Server and NFS Path information in the
appropriate fields.
5. Click Next to configure users or click on the Network, Security or Users link to open the appropriate screen.
To configure users and change the default user passwords:
WARNING: For security reasons, it is recommended you change the default password for both root and admin users immediately.
1. Select the Users link in the content area.
2. Click a username (admin or root) and enter the new password in the Password and Confirm Password fields.
-or-
Click Add to add a user. Enter the new username and password in the appropriate fields.
3. (Optional) To force the user to change the default password, select the User must change password at next
login checkbox.
4. Assign the user to one or more groups.
5. (Optional) Configure account expiration and password expiration.
6. Click Next.
7. Repeat steps 3-7 as needed to configure new user accounts and assign them to default groups.
NOTE: By default, all configured users can access all enabled ports. Additional configuration is needed if your site security policy
requires you to restrict user access to ports.
8. Click Save, then click Finish.
Chapter 3: Accessing the Console Server via the Web Manager 17
- INSTALLER/USER GUIDE 1
- European Union Notification 2
- USA Notification 2
- Canadian Notification 2
- Japanese Notification 2
- Korean Notification 2
- Installer/User Guide 3
- Symbols Used 4
- Introduction 1 5
- Installation 7 5
- Appendices 59 7
- Introduction 9
- Web manager 10
- IPv4 and IPv6 support 10
- Flexible users and groups 10
- Security 10
- Authentication 11
- Packet filtering 11
- Configuration Example 12
- Chapter 1: Introduction 5 13
- Installation 15
- Connecting the Hardware 16
- Turning On the Console Server 19
- Configuring a Console Server 20
- Wizard Mode 24
- Expert Mode 26
- System Tools 26
- DSView 3 software security 27
- FIPS module 27
- HTTPS Certificate 28
- Bootp Configuration Retrieval 29
- Date and Time 30
- Help and Language 30
- Boot Configuration 31
- Information 32
- Settings 32
- IPv4 and IPv6 static routes 33
- Firewall 34
- IPSec(VPN) 36
- SNMP Configuration 37
- Serial ports 38
- Table 3.6: Dial-in Parameters 41
- Table 3.7: Power Parameters 42
- Auxiliary ports 43
- CAS Profile 43
- Auto discovery 44
- Pool of CAS ports 45
- Dial-in Profile 46
- Dial-out Profile 47
- Pluggable Devices 49
- Appliance authentication 50
- Authentication servers 50
- Local accounts 52
- User groups 53
- Managing user groups 55
- Table 3.11: ts_menu Options 56
- DSView software access rights 58
- Event Notifications 59
- Trap Forward 60
- Data Buffering 60
- Appliance logging 60
- Power Management 61
- Outlet Groups 63
- Active Sessions 64
- Monitoring 65
- Change Password 65
- Serial Viewer 66
- App e nd ic e s 67
- DSView 3 Software 69
- Appendix E: Internal Modem 72
- Appendices 65 73
- AT+MS modulation selection 74
- AT S registers 75
- Basic modem result codes 76
- Digital line guard 76
- Sleep mode operation 76
- Disconnecting a call 77
- Selecting country codes 77
- Using caller ID 78
- Appendix F: Technical Support 79
- For Technical Support: 80
Relacionado con productos y manuales para Servidores De Consola Avocent Network Adapter EMS1000P
(96 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.073 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales